Utahraptor Skeleton – Desktop Dromaeosaur 3D Model, 13 Parts

My Utahraptor skeleton as a desktop mount: about 100 cm from the snout to the tip of the tail and 519 mm tall above the board, caught mid-stride with the left foot and its sickle claw off the ground.

13 parts, holes for the steel pins already in the model, and a 25-page assembly manual with a render for every step. Personal licence, download straight after checkout.

€35,00

4 Downloads

About Utahraptor

This Utahraptor skeleton STL builds my reconstruction of the biggest known dromaeosaur as a desktop mount about a metre long. It is caught mid-stride: the right foot is planted, the left foot is off the ground with its sickle claw held up, the jaws are open and the left arm reaches forward. The tail is carried high behind the hips.

Utahraptor ostrommaysorum was named in 1993 by James Kirkland, Robert Gaston and Donald Burge, in the journal Hunteria. The bones come from the Yellow Cat Member of the Cedar Mountain Formation in eastern Utah.

You will often read that it lived 125 million years ago, but newer dating puts those rocks at roughly 139 to 135 million years old, early in the Cretaceous. Adults were around six metres long, and the claw on the second toe of each foot was about 24 cm. The Natural History Museum of Utah has a short page on the animal.

Utahraptor skeleton STL, desktop dromaeosaur skeleton 3D model in side view, mid-stride with the left foot lifted
My Utahraptor in side view, about 100 cm from the snout to the tip of the tail.

At about one sixth of life size it still has the presence of a big predator on a desk. I sculpted it in Blender from the published descriptions and photographs of the fossils. Where the fossils leave a question open, so does the model.

What is in the Utahraptor skeleton STL download

  • 13 STL parts: the pelvis with the sacrum and the heads of both femurs, the two hind limbs (the right foot carries the whole sickle-claw toe), the ribcage in two halves, the tail in three sections, the pectoral girdle with both shoulder blades and the wishbone, the neck with its cervical ribs, the two forelimbs, and the skull with the lower jaw
  • About 100 cm from the snout to the tip of the tail, 420 mm across the arms and about 519 mm tall above the board
  • Holes for the steel already in the parts: 4.2 mm across for the 4 mm rods and pins, and 2.7 mm for the three 2.5 mm pins at the tail tip and in the shoulders
  • A 25-page assembly manual with a render for every step, the cut lengths for the steel and a drilling plan for the base
  • Files in millimetres, ready to print at 100 %

Printer size you need

The kit prints in parts, so your printer only has to fit the biggest one. That is the right hind limb at 294 mm, with the left one at 260 mm. Every other part is under 204 mm.

On a 10-inch resin printer with about 220 mm of build height, the two legs only fit lying at a steep angle, so check them in your slicer before you start. A 14-inch class machine of about 277 × 156 × 300 mm takes every part, and any 300 × 300 × 300 mm FDM printer prints the whole kit.

Utahraptor hips and raised left leg, detail of the 3D printed dinosaur skeleton
The hips and the lifted left leg. The sickle claw on the second toe is held up off the ground.

Printing the Utahraptor skeleton STL

The files come without supports. That is on purpose: where supports go depends on your printer, your resin and how you orient each part, so that call is yours. Keep them off the joint faces and out of the pin holes, because a support inside a hole closes it.

Print the bones solid. Only the pelvis and the two ribcage halves can be hollowed, with 2.5 mm walls and drain holes at the lowest point. On resin use a 0.03 to 0.05 mm layer height and tilt the parts 20 to 30 degrees. On FDM, a 0.2 mm nozzle keeps the ribs, the cervical ribs, the claws and the tail tip sharp. Print the pelvis and the two hind limbs first. They decide whether the finished skeleton stands straight.

Assembly and the base

The Utahraptor skeleton STL goes together in eleven steps. The hind limbs glue onto the pelvis, and the hips and legs then go onto three rods on the base. After that come the two ribcage halves and the tail. The pectoral girdle goes onto the neck on the bench, and the neck then slides back onto the ribcage while the chest rod is pushed up from under the board. The forelimbs go onto their own short pins in the shoulders, and the skull goes on last.

Four 4 mm rods hold the animal up: 443 mm under the neck, 346 mm under the pelvis, 251 mm into the lifted left leg and 125 mm into the right ankle, each with 20 mm in the board. Only the right foot touches the board.

The pins are 4 mm as well, four of 40 mm, two of 60 and one of 58, plus three 2.5 mm pins of 20 mm. The holes are 0.2 mm wider than the steel and the joint faces are cut with 0.15 mm between them, so a print that comes out a little small still goes together. The steel and the board are not included. The manual has the cut lengths and the drilling plan for a 214 × 650 mm board.

If you like this format, the Nanotyrannus skeleton goes together the same way, and the rest of my 3D printed dinosaur files are on the STL page.

Utahraptor desktop skeleton STL on its base, seen from above at the front left
The whole skeleton on its base, seen from the front left.

Questions people ask

Can I print the Utahraptor skeleton STL smaller or bigger?

Yes, as long as you scale every part by the same factor. The pin holes scale with it: at 80 % a 4.2 mm hole becomes 3.4 mm and a 2.7 mm hole 2.2 mm, so you would switch to 3 mm rod and 2 mm pins. The cut lengths in the manual scale by the same factor.

Do I really need the steel?

Yes. Only one foot touches the board and the tail reaches almost 30 cm past the back of it. The rods carry the animal, and the pins keep the neck and the tail from sagging over time. Glue alone will not hold that.

Is the sickle claw a separate part?

No. The first bone of the sickle-claw toe is part of the right hind limb, so the whole toe prints in one piece with the foot. The same goes for the lifted left foot.

Licence

The Utahraptor skeleton STL is for personal use only. You can print it for yourself as often as you like. You may not resell or share the files, sell printed copies, or print it for other people as a service. Commercial licences are available on request. Instant digital download, nothing is shipped.

Reviews

There are no reviews yet.

Be the first to review “Utahraptor Skeleton – Desktop Dromaeosaur 3D Model, 13 Parts”
Scroll to Top