Nanotyrannus Skeleton โ€“ Desktop Tyrannosaur 3D Model, 13 Parts

Jody, my Nanotyrannus skeleton as a desktop mount: about 114 cm from the snout to the tip of the tail and 545 mm tall above the board, caught mid-stride with the left foot off the ground.

13 parts, holes for the steel pins already in the model, and a 25-page assembly manual with a render for every step. Personal licence, download straight after checkout.

€30,00

7 Downloads

About Nanotyrannus

This Nanotyrannus skeleton STL builds Jody, my reconstruction of the small tyrannosaur from the Hell Creek Formation, as a desktop mount a little over a metre long. Jody is caught mid-stride: the left foot is off the ground, the head is held forward with the jaws open, and the tail runs out level behind the hips.

For decades nobody could agree on what Nanotyrannus was. Plenty of palaeontologists read the specimens as teenage Tyrannosaurus rex. In 2025 Lindsay Zanno and James Napoli described the small tyrannosaur preserved with a Triceratops in the Dueling Dinosaurs block from Montana. It was about twenty years old and close to fully grown, so not a young T. rex at all. It has bigger arms, more teeth and fewer tail vertebrae, and the same study named a second species, Nanotyrannus lethaeus. More background on the animal is on Wikipedia.

Nanotyrannus skeleton STL, desktop tyrannosaur skeleton 3D model in side view, mid-stride with the left foot lifted
Jody in side view, about 114 cm from the snout to the tip of the tail.

Where the science is still open, so is the model. I would rather say that than pretend every bone is settled.

What is in the Nanotyrannus skeleton STL download

  • 13 STL parts: the pelvis with the sacrum and the heads of both femurs, two femurs, two lower legs with their feet, the trunk in two halves (the front half carries the neck), the tail in three sections, the scapulae with both arms, the skull with the lower jaw, and the gastralia, the basket of belly ribs
  • About 114 cm from the snout to the tip of the tail, and about 545 mm tall above the board
  • Holes for the steel already in the parts: 4.2 mm across for 4 mm rod, and 2.7 mm for the one 2.5 mm pin near the tail tip
  • A 25-page assembly manual with a render for every step, the rod cut lengths and a drilling plan for the base
  • Files in millimetres, ready to print at 100 %

The skeleton is split into sections, not into single bones. Fewer joints means a straighter skeleton at the end. Most cuts sit between two vertebrae or at the knee; only the femur is cut, just below its head, so the hip joint stays in one piece.

Nanotyrannus skull with the jaws open, detail of the 3D printable skeleton
The skull and lower jaw print as one part.

Printer size you need

This is a big desktop piece, and a few parts of the Nanotyrannus skeleton STL are big too. The longest are the two lower legs with their feet, 295 and 284 mm, and the first tail section at 278 mm. The front trunk with the neck measures 206 ร— 172 ร— 147 mm.

That rules out a 10-inch resin printer such as the Elegoo Saturn 4 Ultra 16K (211.68 ร— 118.37 ร— 220 mm): the front trunk does not fit. For resin you want a 14-inch class machine of about 277 ร— 156 ร— 300 mm. Any 300 ร— 300 ร— 300 mm FDM printer takes the whole kit.

Nanotyrannus feet and claws, detail of the 3D printed dinosaur skeleton
The feet. The left one is lifted mid-stride, the right one carries the weight.

Printing the Nanotyrannus skeleton STL

The files come without supports. That is on purpose: where supports go depends on your printer, your resin and how you orient each part, so that call is yours. Keep supports off the joint faces and out of the pin holes, because a support inside a hole closes it.

Print the bones solid. Only the pelvis and the two trunk halves can be hollowed, with 2.5 mm walls and drain holes at the lowest point. On resin use a 0.03 to 0.05 mm layer height and tilt the parts 20 to 30 degrees. On FDM, a 0.2 mm nozzle keeps the ribs, the cervical ribs, the gastralia and the claws sharp. Print the gastralia with the sleeve upright, so the rod hole comes out as a clean vertical bore. Print the pelvis, the femurs and the lower legs first: they decide whether the finished skeleton stands straight.

Assembly and the base

The Nanotyrannus skeleton STL goes together in eleven steps. The femurs go onto the pelvis first, then the lower legs, and then the hips and legs go onto their rods on the base. Then the gastralia slide down the chest rod on a sleeve of their own. They have to go on before the ribcage, because once the front trunk sits on that rod you can’t get them over it anymore. After that the ribcage, the tail, the scapulae with the arms, and the skull last.

Four 4 mm rods hold the animal above the board, so neither foot touches it: 505 mm under the chest, 516 mm under the tail, 212 mm into the left leg and 108 mm into the right foot. With the pins that comes to 1686 mm of 4 mm rod, plus 40 mm of 2.5 mm rod, all cut by you to the lengths in the manual. Use two-part epoxy on everything that carries weight.

Nanotyrannus ribcage, shoulder girdle and arm, close-up of the skeleton 3D model
The front of the ribcage with the shoulder girdle and the arm.

The base is not part of the download. The manual gives the board size, 292 ร— 731 mm, and exactly where to drill the four rod holes. If you like this format, the Iguanodon skeleton and the Jeholosaurus skeleton go together the same way, and the rest of my 3D printed dinosaur files are in the shop.

Nanotyrannus skeleton 3D model, left side view of the whole skeleton
The whole skeleton from the left side.

Questions people ask

Can I print the Nanotyrannus skeleton STL smaller or bigger?

Yes, as long as you scale every part by the same factor. The pin holes scale with it: at 80 % a 4.2 mm hole becomes 3.4 mm, so you would switch to 3 mm rod, and the cut lengths in the manual scale by the same factor.

Do I really need the steel rods?

Yes. Neither foot touches the board, so the four rods carry the whole animal, and the pins keep the trunk and the tail from sagging over time. Glue alone will not hold a tail that reaches this far behind the hips.

Is there a life-size version?

There is, but only for museums and educational programmes. If that is you, get in touch through the contact page.

Licence

The Nanotyrannus skeleton STL is for personal use only. You can print it for yourself as often as you like. You may not resell or share the files, sell printed copies, or print it for other people as a service. Commercial licences are available on request. Instant digital download, nothing is shipped.

Reviews

There are no reviews yet.

Be the first to review “Nanotyrannus Skeleton โ€“ Desktop Tyrannosaur 3D Model, 13 Parts”
Scroll to Top